StoreCom Equipment LLC
1102 E. Dixie Dr.
West Carrollton OH  45449


PROUDLY MADE
IN THE USA

800-356-0368 “Simple Communications For A Not So Simple World” Fund Free Mammograms Fund Animal Shelters

Charities We Support

Please give them
a click

PDF Cutsheets

HOW TO ORDER STORECOM’S

200GCBB

201GCB

202GCB

200 SERIES DESK PHONES

200BPA

301GCB

302GCB

303GCB

303GEB

300 SERIES DESK PHONES

300BPA

SC-3

SC-3D DESK PHONE

300BPAU

SC-4

SC-44

PAGEKOM COMPATIBLE DESK PHONES

300BPAP

OPTIONS

Phased & Confused: A guide

70 volts systems

PDF Reader Free

StoreCom Home

NOTE TO INSTALLER

The intercoms are wired with telephone Quad wire which is a 22-24 awg solid copper wire or CAT5 wire which is also a 22-24 awg solid copper wire, no shields. The color code is as follows: Green - Red - Yellow - Black. Using CAT 5 choose a color of wire for the function, ie white/orange for talk #1, and use this color all the way through the installation. This will prevent miswiring and confusion for other servicers.

Intercoms are daisy chained together - this means that each intercom is directly connected to the next intercom in the chain, not run all the way back to the page adapter.

TO INSTALL PAGE ADAPTOR/POWER SUPPLY

Locate the page adaptor/power supply close to the audio amplifier (it is wise to plug the amplifier into the same power strip or outlet as the page adaptor to tie all the grounds together). The page adaptor output going into the amplifier AUX input. The page adaptor can be wall mounted or set on a shelf. Before hooking units to page adaptor, hook up the music receiver and adjust your music levels and make sure everything is functioning correctly. We suggest that you take one phone and hook it to the page adaptor. Adjust the levels for optimum performance before installing rest of the phones.

STORE WIRING

Our intercoms are daisy chained but our suggestion is that two separate runs of wire be installed to create two zones, eliminating problems. One run daisy chained to the front registers and the other one to the back of the store to run the other departments. When using the existing microphone wires, to upgrade to our 301 system, use the shield as common. Make sure that the shield is NOT GROUNDED AT ANY POINT IN THE SYSTEM. Determine whether or not it is grounded, take your ohm meter and put one lead on the shield and one on an AC outlet center ground pin. You should read Infinity on the meter.

MOUNTING OF INTERCOMS

The StoreCom intercom can be mounted on any surface. Wall board, paneling, counters, metal and plastic. The back plate is designed to be flush mounted on these surfaces. The wiring can be brought through the hole in the middle of the back plate. Do not put terminals on the ends of the wires, strip and wrap around the screws attached to the back. DO NOT CHANGE THE WIRING OF THE PIGTAIL. Each phone has a metal lip at the top. Hook this lip over the lip of the back. Swing phone down to meet the riser and U-nut. Screw in 8/32 x 1" bolt snugly but not too tight. Checkstands that are exclusively made to fit our phones are available separately.

Copyright 2014 StoreCom Equipment LLC
Contact Webmaster Short Run Grafx

Helpful hints for installing StoreCom Intercoms in your store, plant, factory or warehouse. Need more help? Call us @ 1-800-356-0368 for live help.

StoreCom Intercom back plate StoreCom intercom wiring example How to attach the StoreCom Intercom to the backplate Securing the StoreCom Intercom to the backplate How to hook the pigtail to a StoreCom Intercom A StoreCom Intercom Checkstand How to wire the StoreCom Intercom pigtail

Our installation video is right HERE!